| Product characteristics | |||||
|---|---|---|---|---|---|
| Number of inputs and outputs | Number of digital outputs: 1; Number of analogue outputs: 1 | ||||
| Measuring range |
| ||||
| Process connection | threaded connection G 1/2 sealing cone | ||||
| Installation length EL [mm] | 50 | ||||
| Application | |||||
| Special feature | Gold-plated contacts | ||||
| Measuring element | 1 x Pt 1000 | ||||
| Reference element | 1 x NTC | ||||
| Media | liquids and gases | ||||
| Pressure rating [bar] | 160 | ||||
| Electrical data | |||||
| Operating voltage [V] | 18…32 DC; (“supply class 2” to cULus) | ||||
| Current consumption [mA] | 10; (24 V) | ||||
| Protection class | III | ||||
| Reverse polarity protection | yes | ||||
| Power-on delay time [s] | 6 | ||||
| Integrated watchdog | yes | ||||
| Inputs / outputs | |||||
| Number of inputs and outputs | Number of digital outputs: 1; Number of analogue outputs: 1 | ||||
| Outputs | |||||
| Total number of outputs | 2 | ||||
| Output signal | analogue signal; IO-Link; calibration check status | ||||
| Electrical design | PNP/NPN | ||||
| Number of digital outputs | 1 | ||||
| Output function | normally open; (diagnostic signal) | ||||
| Max. voltage drop switching output DC [V] | 2 | ||||
| Permanent current rating of switching output DC [mA] | 100 | ||||
| Diagnostic output | calibration check status and error diagnostics | ||||
| Number of analogue outputs | 1 | ||||
| Analogue current output [mA] | 4…20 | ||||
| Max. load [Ω] | (Ub – 15 V) x 50 | ||||
| Short-circuit protection | yes | ||||
| Type of short-circuit protection | pulsed | ||||
| Overload protection | yes | ||||
| Measuring/setting range | |||||
| Measuring range |
| ||||
| Note on measuring range |
| ||||
| Factory setting | -10…150 °C / 14…302 °F | ||||
| Calibration check limit [K] | 0.5…3 | ||||
| In steps of [K] | 0.05 | ||||
| Resolution | |||||
| Resolution of analogue output [K] | 0.05 | ||||
| Accuracy / deviations | |||||
| Precision analogue output [K] | ± 0,2 | ||||
| Precision IO-Link [K] | ± 0,2 | ||||
| Temperature coefficient analogue output [% of the span / 10 K] | < ± 0,02; (in case of deviation from the reference condition 25 ± 5 °C) | ||||
| Temperature coefficient IO-Link [% of the span / 10 K] | < ± 0,01; (in case of deviation from the reference condition 25 ± 5 °C) | ||||
| Response times | |||||
| Dynamic response T05 / T09 [s] | 1,5 / 4 | ||||
| Software / programming | |||||
| Parameter setting options | Display unit; scaling of the analogue output; calibration check limit; switching logic diagnostic output; simulation mode | ||||
| Interfaces | |||||
| Communication interface | IO-Link | ||||
| Transmission type | COM2 (38,4 kBaud) | ||||
| IO-Link revision | 1.1 | ||||
| SDCI standard | IEC 61131-9 CDV | ||||
| Profiles | Digital Measuring Sensor, Common Profile, Blob Transfer | ||||
| SIO mode | yes | ||||
| Required master port type | A | ||||
| Process data analogue | 1 | ||||
| Process data binary | 1 | ||||
| Min. process cycle time [ms] | 4.4 | ||||
| IO-Link resolution temperature [K] | 0.01 | ||||
| Supported DeviceIDs |
| ||||
| Operating conditions | |||||
| Ambient temperature [°C] | -25…70 | ||||
| Note on ambient temperature |
| ||||
| Storage temperature [°C] | -40…100 | ||||
| Protection | IP 68; IP 69K | ||||
| Mechanical data | |||||
| Weight [g] | 366.9 | ||||
| Dimensions [mm] | Ø 50 / L = 144 | ||||
| Materials | stainless steel (1.4404 / 316L); PEI; FKM; PFA | ||||
| Materials (wetted parts) | stainless steel (1.4404 / 316L); PEEK | ||||
| Process connection | threaded connection G 1/2 sealing cone | ||||
| Surface characteristics Ra/Rz of the wetted parts | Ra: < 0.8 | ||||
| Probe diameter [mm] | 6 | ||||
| Installation length EL [mm] | 50 | ||||
| Remarks | |||||
| Remarks |
| ||||
| Pack quantity | 1 pcs. | ||||
| Electrical connection | |||||
| Connection | Connector: 1 x M12; Contacts: gold-plated | ||||
